The OBDII trouble password of P0335 is recognized as a “hard” code, an interpretation severely detrimental to the procedure of your Accord engine. An ext specifically the DTC P0335 represents a absence of signal from the crankshaft position sensor. The crankshaft position sensor in your Honda Accord informs your ECU that the crankshaft speed and also current location.

You are watching: 2000 honda accord camshaft position sensor

Without this data, the engine will certainly either no run or run very poorly. Common symptoms are challenge starting or the engine may shut turn off randomly, developing a very dangerous case for not just the driver however the passengers as well.

Possible causes of OBDII examine engine light P0335Bad or weak batteryBad StarterBad crankshaft position sensorDamaged sensor harness

Today I’ll be mirroring you how to service and also replace her crankshaft place sensor in a 2000 Honda Accord with a F23A1 VTEC SOHC engine.

The part number for this part is 37840-P0A-A01 because that the crankshaft place sensor in her Honda Accord. The can also be discovered under the part number of 37840-PAA-A01.


*

This How To readjust a Honda Accord Crankshaft position Sensor DIY overview assumes girlfriend have already removed her driver side engine mount and also supported her engine v a jack. Please inspect our exactly how To readjust a Honda Accord time Belt guide for an ext details.

Before you start our DIY overview on exactly how To change a Honda Accord Crankshaft place Sensor, you must disconnect the negative terminal on her battery. As proclaimed previously, this overview assumes you can raise and lower her F23 already, i m sorry is mandatory when changing your time belt.

*

Unplug your four pin connector the runs to her crankshaft place sensor in your Honda Accord. Here’s what your pigtail look at like mounted to your F23A1. It’s secured through a 10mm bolt the runs through the ago of your VTEC SOHC engine.

*

This exploit to your crankshaft position sensor runs v your reduced timing plate, which should be gotten rid of to change a Honda Accord Crankshaft place Sensor. In bespeak to execute this, you must reduced your engine if still associated to her chassis, and also remove the crankshaft pulley or harmonic balancer.

This may be an overwhelming if you room working on the ground with hand tools and also don’t have a wait compressor v the appropriate air tools. Use a Honda crankshaft wrench, Moroso part number 61805 to properly loosen your crankshaft bolt without air tools.

*

With the bolt removed, you should be able to wiggle off her crankshaft wheel and set it safely come the side. Do sure eliminate your woodruff an essential and store that as safe as your pulley.

*

Now you have the right to remove all the 10mm bolts that hold your lower timing cover in place. Remove these special bolts and then do your method to the valve cover, you will need to earlier off the valve sheathe bolts that run through to the cylinder head.

Loosen every the valve cover bolts, yet do no remove and also gently loosen her valve cover. Elevator the valve cover to permit enough room for your top SOHC VTEC timing cover to come off her engine. There space 2 10mm bolts the run v the upper cover to the cylinder head, remove these to ease your top timing cover.

*

Now slide turn off your lower timing cover and pull down to release from your side motor mount. You must now watch your timing belt assembly and also your F23A1 balance shafts and also belts. The crankshaft place sensor in her Honda Accord is located behind the crank create plate.

*

You have the right to take one of two routes to removing your crankshaft place sensor and also replacing it. You have the right to loosen her timing belt tensioner bolt, the longated bolt located in the middle of your tensioner arm. This should permit enough slack regarding gently back off your lower crank wheel plate and undo the 10mm bolt that holds the crankshaft position sensor in place.

*

If this is not an alternative for you, examine out our exactly how To change a Honda Accord timing Belt overview on exactly how to effectively time and also remove your F23A1 belts to business your crankshaft position sensor.

There are several timing marks for your balance obelisk that we recommend friend line up to TDC before removing your balance obelisk belts.

See more: Folklore: What Do Leprechauns Eat And Drink ? 4 Ways To Catch A Leprechaun

*

Before removing her balance column belts to reach your crankshaft position sensor, friend will need to dual check timing marks come ensure your F23a1 is at TDC. Again for more details examine our how To DIY overview on changing the Honda Accord timing belt.

*

Once you have actually replaced her Honda Accord crankshaft place sensor, you can use a scan device to properly clear your OBDII examine engine password of P0335. Hope we’ve helped you learn exactly how To change a Honda Accord Crankshaft position Sensor, if you have any type of questions you re welcome leave united state a comment below!