My automobile has behind sliding doors, appropriate side is power and left side is manual. Both doors will not open and also are do a sound favor they space unlocking however do not. It has a defense system. How have the right to I number out what the difficulty is for this reason I have the right to repair it? no door can be opened up or unlocked.


You are watching: 2001 oldsmobile silhouette power sliding door problems

*

friend will have to shot to traction door dashboard off inside vehicle, not simple to carry out then watch if a clip is damaged or a cable is damaged that operates it. Also shot lubing latch from inside when panel is off. See picture there is a distinct tool needed for door handle removal.
*

*

*

*

once I push the door button to open up the slide door ns hear a solenoid sound, the very same is true if I usage the switch on the DIC. If I open the door manually native the outside the door will open under its own power. If I press the door lever on the inside then it will certainly pop open and start moving on the own.If the door is open pressing either switch will cause the door come close.Any ideas?Russ
The noise ns hear sounds prefer a solenoid, that is sounds favor it is behind the inside door handle of the passenger side slider.When using:Remote: solenoid noise.DIC switch: solenoid noise.Switch of structure behind passenger door: solenoid noise.Using door handle inside car: door will certainly pop out and move backward.Using outside door handle: door will start to move backwards.
Think what is happening is solenoid the unlatches lock need adjustmet if possible. Eliminate door panel and give a look together you operate.
I have actually duel strength doors. The driver side power door closes however the "door open" alarm go off when I put vehicle in drive. I need to disable this power door from mine console to do alarm go off.I noticed that sometimes when it closes it opens up right up together if something is in the way. I also noticed that the motor operation (it renders a whining sound) even after door is shut. As soon as motor stops, the back part of the door pops out a little bit and also then latches.I have the right to open and close door manually through power door disabled.


See more: How To Delete Save File Pokemon Omega Ruby And Alpha Sapphire Wiki Guide

try re-initializing the door first.System is equipped with self diagnostics and also you need to get in it to examine for problem codes. Allow me know what girlfriend find.ON-BOARD DIAGNOSTIC FEATURESThe left and also right power sliding door systems operate as independent systems. The on-board diagnostic modes are entered and also operate the very same in both systems.The strength sliding door solution are qualified of the following on-board diagnostic functions: Diagnostic mode 1: one audible signal indicates the diagnostic problem codes stored by the behind side door actuator manage module. Diagnostic setting 2: an audible signal suggests when inputs come the behind side door actuator regulate module space active. Diagnostic mode 3: Performs an output test of the slide door unlatch actuator.Entering On-Board DiagnosticsThe on-board diagnostic modes have the right to only be entered in a sequential stimulate from modes 1 - 3. get in the best power sliding door system on-board diagnostics utilizing the right B-pillar open/close switch and also the right on/off switch in the overhead console. enter the left strength sliding door system on-board diagnostics using the left B-pillar open/close switch and also the left on/off move in the overhead console. 1. Both power sliding doors must be closed and also in the latched position. 2. Ar the on/off move in the overhead console to the OFF position 3. Press and hold the B-pillar strength sliding door open/close switch. 4. While holding the open/close switch, operate the on/off switch v 10 ON and also OFF cycles in ~ 10 seconds stopping in the ~ above position. 5. The sliding door alarm will sound 1 long tone indicating diagnostic mode 1 is active.Diagnostic mode 1Upon activating diagnostic mode 1, DTCs will start to be signaled by the slide door alarm. The DTCs are 2 digit codes and also the codes are represented by the number of buzzes because that each number of the password number. For instance a DTC 12 is represented with the following sequence: buzz, pause, buzz, lengthy pause. Every DTC will be signaled 3 times before proceeding to the following DTC. Refer to Diagnostic Trouble code (DTC) List. The DTCs will continue to be repeated in this manner until the on-board diagnostics room existed or mode 2 is entered. Once existing the on-board diagnostics all stored DTCs will be erased native the behind side door actuator manage module memory.Diagnostic setting 2Enter the diagnostic setting 2 from mode 1 through proceeding through the adhering to steps: 1. Press and hold the power sliding door open/close switch for 4 seconds. 2. Release the open/close switch once the alarm begins to sound. 3. The alarm will sound 2 long tones describe diagnostic mode 2 is active.During diagnostic mode 2 the slide door alert is offered to suggest when the adhering to inputs to the behind side door actuator regulate module room activated:The power Sliding Door On/Off Switch: turn the on/off switch off and on. The alarm will certainly sound one quick tone as soon as the move is turned indigenous the off to ~ above position.The power Sliding Door Open/Close switch in the Overhead Console: press the power sliding door open/close switch in the overhead console. The alarm will sound because that as lengthy as the move is held in the open position.The power Sliding Door B-pillar Open/Close Switch: push the strength sliding door B-pillar open/close switch. The alarm will certainly sound for as long as the switch is organized in the open position.The Keyless Entry mechanism Open/Close Command: push the open/close switch on the keyless entrance transmitter. The alarm will sound one short tone whenever an open up or nearby command is received from the keyless entry system.The slide Door Detent Switch: turn the on/off switch off and also slowly open and close the slide door. The alarm will certainly sound at any time the detent switch signal circuit is pulled to ground, suggested by 2 tones together the door is moved in between the open and fully latched positions.The Ignition switch On Signal: revolve the ignition switch on. The alarm will sound because that as lengthy as the ignition move is in the top top position.The Transaxle variety Switch Park Position: use the brakes and move the transmission selector lever out of the park position. The alarm will sound because that as long as the transaxle is out of park.Diagnostic setting 3Enter the diagnostic mode 3 from mode 2 by proceeding through the adhering to steps: 1. Press and hold the power sliding door open/close switch for 4 seconds. 2. Relax the open/close switch once the alarm begins to sound. 3. The alarm will certainly sound 3 long tones indicating diagnostic mode 3 is active.Diagnostic mode 3 exam the procedure of the sliding door unlatched actuator. Begin with the sliding door in the closed and latched position. Press either that the open/close switches and the power sliding door unlatch actuator will be energized unlatching the door. Once the unlatch actuator is energized the door alarm will sound briefly. As long as the door lock switch plate plungers and also pads stay in contact the open/close switch may be pressed and the unlock actuator will certainly be energized and also alarm sounded.Exiting On-Board DiagnosticsWhen exiting the on-board diagnostics any DTCs save by the behind side door actuator manage module will be erased. In bespeak to evaluation the DTCs, diagnostic setting 1 might be entered from setting 3 by pushing the strength sliding door open/close switch for 4 seconds. The on-board diagnostics may be exited native diagnostic modes 1 or 3 by transforming power door on/off switch to the off place for a minimum that 10 seconds. After exiting the on-board diagnostics the strength sliding door need to be reinitialized. Describe POWER sliding DOOR (PSD) REINITIALIZATION.POWER sliding DOOR (PSD) RE-INITIALIZATIONThe behind side door actuator control modules monitor the power sliding door positions at all times. At any time the battery hopeful voltage it is provided to a rear side door actuator regulate module has actually been eliminated or the on-board diagnostics have been activated, the strength sliding door system(s) need to be re-initialized. Re-initialize the appropriate or left strength sliding door systems using the complying with steps: 1. Revolve the ON/OFF switch for the power sliding door device to it is in re-initialized come the turn off position. 2. Manually open up the strength sliding door completely. 3. Manually close and latch the strength sliding door. 4. Rotate the power sliding door ON/OFF switch to the on position. 5. Open up the power sliding door completely using the B-pillar or overhead console OPEN/CLOSE switch. 5. Close the strength sliding door fully using the B-pillar or overhead console OPEN/CLOSE switch.